This is the COMPLETE Operating Instructions Manual for the Linde Electric ForkLift Truck 386-01 Series; Models E12-01, E14-01, E15-01, E16-01, E18-01, E20-01.
This Manual Describes Procedures for Operation, Handling, Lubrication, Maintenance, Checking, and Adjustment. it will help the operator or anyone Realize Peak Performance Through Effective, Economical and Safe Machine Operation and Maintenance.
Models Covered:
E12-01
E14-01
E15-01
E16-01
E18-01
E20-01
Operating Instructions Manual Contains:
=========
1. Introduction
Your industrial truck
Intended use
Impermissible use
Description of use and climatic conditions
Symbols used
Technical Description
Receiving the industrial truck
Legal requirements for placing on the market
2. Safety
Safety guidelines
Residual risks
Stability
In the case of tip-over
Handling consumables
Competent person
Regulations
Fit attachments
Fork carriage emergency lowering
Emergency exit with attached rear window
3. Overview
Identification plate
Vehicle overview
Controls
Display unit
Switch panel
4. Operation
Service plan before initial commissioning
Instructions for running-in
Pre-shift checks
Standard equipment
Entering and exitingthe truck
Adjusting driver’s seat
Armrest
Adjusting the steering column
Setting the time
Seat belt
Switching the truck on and off
Driving (dual-pedal operation)
Driving (single-pedal operation)
Steering system
Brake system
Warning horn
JoystickCentral lever operation
Joystick — single lever operation
Emergency stop switch
Special equipment
Adjusting the driver’s seat equipped with air suspension
Adjusting the driver’s seat with rotating device
Mast positioning
Lift height limitation
Lift height indicator
Steering angle display
Depressurisation
Lighting
Windscreen wipers
Window heater
Heating system
Linde Forklift Data Management (LFM)
Integrated charger(Linde Power Source)
Electrolyte circulation
Driving speed reduction via a switch
Joystickwith 3rd auxiliary hydraulics
Working under load
Before load pick up
Adjust fork arm distance
Load pick up
Driving under load
Setting down loads
Towing device
Loading / Transporting
Removing the lift mast
Driving without the lift mast
Crane loading
Transportation by lorry or low loading trucks
Leaving the truck
Before leaving the truck
Towing device
5. Maintenance
General remarks
Inspection and maintenance data
Consumables
Inspection and maintenance overview
One-off service plan after 1000 hours
Service plan 1000 hours
Service plan 3000 hours
Service plan 6000 hours
Gearbox
Planetary transmission – Checking the mounting
Changing the oil in the planetary transmission
Checking the planetary transmission oil level
Checking the planetary transmission for leaks
Drive axle – Checking mountings
Checking and adjusting the side stops on the drive axle
Checking the condition and mounting of the spring elements on the drive axle
Chassis, bodywork and fittings
Cleaning the industrial truck
Checking the mountings – Counterweight at the chassis, overhead guard
Opening and closing the battery hood
Checking and adjusting the battery door interlock
Seat belt – Checking the condition and correct operation
Check other bearings and joints and oil
Other cleaning and greasing
Chassis frame
Testing the brake system
Checking the tyres
Changing wheels
Tighten wheel fastenings
Checking the condition of the antistatic belt
Cleaning the turntable steering axle
Cleaning and lubricating the combined axle
Checking the drive axle heat sinks for contamination, cleaning if necessary
Checking and adjusting the side stops on the drive axle
Operating devices
Adjust drive control pedal system
Check pedals and linkage and oil
Check bellows on joystick
Checking the horn for correct function
Adjusting the joysticks
Electrics / Electronics
Checking the battery charge status
Recharging the battery
Connecting the battery to an external battery charger
Battery replacement
Checking the main contactor (switch-on contactor)
Cleaning the fans – Checking for correct operation
Checking the electrical wires
Hydraulics
Working and steering hydraulics – Checking the oil level
Working and steering hydraulics – Checking for leaks
Changing the hydraulic oil
Changing the breather filter
Changing the pressure filter
Suction filter
Checking the control unit for correct function
Double hoses: Checking the pre-tension
Tilt cylinder bearings – Checking for wear
Load lift system
Working on the lift mast and at the front of the truck
Tightening the lift mast mounting
Cleaning and spraying the lift mast chain
Lift mast — adjusting the chain
Checking the mounting, condition and function of the lift mast, lift mast chains, lift cylinders and end stops
Checking the hose carrier
Check fork arms and arm safety devices
Special equipment
Washer system (special equipments) Topping up water tank .
Cleaning and lubricating the sideshift (special equipment), checking the fastening
Cleaning and lubricating the fork prong positioner (special equipment), checking the mounting
Checking the slide guides on the sideshift (special equipment) for wear
Self-help
Fuses – Basic equipment
Fuses – Special equipment
Diagnostic connector
Towing regulations
Malfunctions during operation
Shutting down
Shutting down the industrial truck
Disposal of old trucks
=========
** Model Specification: Linde E12-01, E14-01, E15-01, E16-01, E18-01, E20-01 Electric ForkLift Truck 386-01 Series
** Language: English
** Total Pages: 306
** File Format: PDF
** Requirements: Adobe PDF Reader
** Compatible: All Versions of Windows & Mac, Linux OS, Iphone, Ipad, Android etc…
=========
This QUALITY manual is 100 percents COMPLETE and INTACT,
no MISSING/CORRUPT pages/sections to freak you out! It also is Bookmarked and SEARCHABLE to make what you need easy to find. Complete download comes in PDF format which can work under all PC based Windows operating system and Mac also. It saves to your hard-drive and can be burned to CD-ROM. It can be viewed on any computer, as well as zoomed and printed.
This manual is INSTANT DOWNLOAD. It means no shipping cost or waiting for a CD / paper manual to Arrive in the Mail. You Will receive this Manual today via Instant Download on Completion of Payment via our secure Payment Processor. We Accept All Major Credit/Debit Cards and Paypal. Buy From us and I Guarantee You’ll be a Satisfied Customer and Contact us if You have any Questions.
After your payment is submitted, The Download Link will appear at the checkout page and it will also be sent to your E-Mail Address.
Thanks for Visiting!